Did you know?

Place litter mats or rugs in front of the unit. The Litter-Robot will now perform an initial clean cycle. Need help? Visit whiskersupport.com Use clumping litter or litter beads and crystals that are small enough to pass through the screen. Add litter until it meets the raised MAX fill line when spread flat (8-10 lbs or 3.6-4.5 kg). Be careful ... Oct 19, 2020 · If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by excess weight. Easy fix on how to get rid of that annoying flashing yellow light on your Litter Robot 3. Litter can build up on your Pinch detect bar(sensor) inside the bas...This video will show you what the DFI sensors are. What do they do, where are they, how they work and how to clean them. Also a quick tip on fixing a common ...Like Comment Share The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to.Inspect the Position Sensor. If you've just installed and/or replaced the Connect Upgrade Kit, the Drawer Full Indicator, Motor, Control Panel, or any other components within the motor cavity in your unit, and now you're getting three flashing lights, it is most likely due to the Position Sensor being out of place. Power off and unplug the unit.litterrobot • 2 yr. ago. If the Litter-Robot 3 cannot find Dump and/or Home position, the control panel will display 3 lights blinking either left to right, right to left or all three simultaneously. *PLEASE NOTE: If you have recently disassembled your globe (split it at the vertical axis), please advise. If you have not disassembled the ...When the Litter-Robot 3 Connect initially arrived, we were shocked at the sheer dimension of the box. The box is so big since the unit comes pre-assembled. With the Wi-Fi made it possible for version, there are also a couple of steps to get it synced with your phone.To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base. 2.) Wait 10 seconds then plug the unit back in. 3.) Allow the unit to complete a startup cycle.There are a few reasons why your Litter Robot may be blinking blue light. One reason may be that the Litter Robot is low on power and needs to be recharged. Another reason may be that the Litter Robot is full and needs to be emptied. Lastly, the blue light may be blinking because there is a problem with the Litter Robot and it needs …http://www.litter-robot.com/If your Litter-Robot 3 is stopping mid-cycle, check out this helpful troubleshooting video to help remedy the problem. We’ve put ...Check for excess weight, such as too much litter or waste. When you are done, press the Reset button or turn the unit off then back on to reset the Cat Sensor. If the cycling light is slowly flashing yellow (about once per second) or you are receiving a Cycle interrupted or Bonnet removed notification, this indicates a cycle has been ... Place litter mats or rugs in front of the unit. The Litter-Robot will now perform an initial clean cycle. Need help? Visit whiskersupport.com Use clumping litter or litter beads and crystals that are small enough to pass through the screen. Add litter until it meets the raised MAX fill line when spread flat (8-10 lbs or 3.6-4.5 kg). Be careful ...Inspect the Position Sensor. If you've just installed You'll most commonly notice a flashing or blinkingDisconnect the bonnet. Gently flex the two front bonnet ta Hi Roboteers, Just last week our litter robot started a strange behaviour of ending its cleaning cycle upside-down. It would rotate to empty the waste and would only return just enough so that the waste chute was just past the opening and then stop. The solid blue light would come on indicating that it is ready for action. However the unused litter is still trapped in the reservoir. We ran a ...Feb 23, 2023 · A solid blue and yellow light may flash and remain illuminated simultaneously. This indicates that your Litter-Robot has entered its 8-Hour Sleep Mode. To deactivate this, just press and hold the Cycle button and the machine will be ready once again. However, the simultaneous flashing of all colored lights is a big problem. Hi, The following troubleshooting should resolve the

Mar 16, 2017 · 4. Put the Globe back on the base unit and ensure that it is on the track. If you feel that the Globe is heavy to one side or another, check in the Litter Pocket to make sure that there is no wet or clumped litter stuck that is throwing off the weight of the unit during cycling. Ensure the Globe is filled to the Fill Line and not above the Fill ... If I disconnect the unit from the power and turn back on the only light which comes on is the solid yellow cycling light. The on, cycle and reset button on my base …Disconnect the bonnet. Gently flex the two front bonnet tabs outward as close to a 90-degree angle as you can and hold for 20-30 seconds. This will remold the tabs to have a more secure connection. Reattach the bonnet. There are four tabs total: two curved tabs in the back, two on the sides.1 Like mechatanguay December 7, 2020, 6:28am 3 Hi, The middle yellow light blinks fast. It sometimes gets stuck at the very start of the cycle (that is it attempts to move but fails and fast blink yellow). Other times it gets stuck during cycling when it is is about to go backward (see attached picture). My serial number is: LR3133558Step 1: Check the Waste Drawer. The first step in troubleshooting a rapidly flashing yellow light on the Litter Robot is to check the waste drawer. If the drawer is full, the light will flash rapidly to indicate that it needs to be emptied. To check the waste drawer, simply open the door at the bottom of the unit and remove the drawer.

Please follow the steps below. Open your app. Go to “Remote” and click “Delete my Litter-Robot.”. Completely close the Litter-Robot app. Reset your Litter …The following are the typical causes of why your Litter-Robot is having torque issues: 1. Motor Obstruction. The globe of the Litter-Robot can get jammed at one point while using the litter box. This …Fill your Litter-Robot to the fill line with litter and then perform a hard reset on your unit. Here’s how to do a hard reset on your Litter-Robot 4: Press and hold the Reset and Power buttons for 3 seconds. The light bar will flash red then go through a sequence of red, blue and green lights then begin a cycle.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Excess weight will put a strain on the motor and can cause the un. Possible cause: Got my Litter robot yesterday and have a similar issue. Brand new out of th.